Pool Pump Sheds by SlatMe

A Pool Pump Cover from SlatMe is the perfect finishing touch for your pool area, providing an ideal solution for screening your pool equipment and ensuring your pool area gets noticed for all the right reasons. Strike the perfect balance between good looks and smart design with a premium pool pump shed from SlatMe.

SlatMe's Free Standing Pool Filter Cover is a stand-alone unit that includes a rear panel and is designed for direct fixing onto a concrete slab. It's the perfect design for areas where fixing onto a wall isn't possible.

As the higest quality pool filter covers available on the market, SlatMe offers:

Exceptional quality and value
Fully operable gates and lids for easy access to your pool equipment
Pre-constructed panels for quicker assembly
Expertly welded slats and frames for added strength
Low maintenance and durable design
Genuine Interpon powder coat in a range of contemporary colours
Superior craftsmanship and construction
5 Year Limited Manufacturer's Warranty

For approximate internal clearances, take 60 mm off the depth; 55 mm off the height and 55 mm off the width. Allow for a 45 mm fall on the lid.

Lids are designed to open approximately 45 degrees. Please ask for custom gas struts if you need a wider opening.

Please read the recommended uses section to confirm if this product is suitable for you.

We've packed a lot into our DIY kits, including:

Pre-contructed aluminium gate and side panels
A solid, weather resistant VJ style lid opening to approx. 45 degrees
Welded slats, frames and joins throughout
Calibrated gas struts for safe and easy lid operation
Quality gate hardware, including a genuine D&D gate latch
Colour matched hinges, screws and fixings
Detailed instruction sheet with optional phone support
5 Year Limited Manufacturer's Warranty

Lids are designed to open approximately 45 degrees. Please ask for custom gas struts if you need a wider opening.
For approximate internal clearances, take 60 mm off the depth; 55 mm off the height and 55 mm off the width. Allow for a 45 mm fall on the lid.
SlatMe pool pump covers are suitable for covering standard pool filtration systems and pool pumps.
Covers are not recommended for heat pumps, air conditioners, or other heat emitting equipment (due to the restricted air flow). Please refer to the FAQs page for more information.
Pool Pump Covers are best installed outside the non-climbable zone of your pool fencing, but installations within the non-climbable zone are possible in certain circumstances, depending on the specific layout of your site, as advised by a local pool safety certifier.
The Free Standing Pool Pump Cover has four feet that require fixing into a concrete slab or similar footing. Contact us to discuss options if you need to install into natural ground.
The location of your pool pump cover in relation to your pool fencing must meet the pool safety requirements of your local council. Please confirm your local council's pool safety requirements prior to purchase.
Any installations within the non-climbable zone of your pool fencing must have the gates oriented correctly to ensure pool safety compliance. Please contact us for more information if you are unsure.

Our DIY Kits can be assembled within 2 to 4 hours by a tradesman or experienced home handyman. Pre-welded, fully constructed panels save time on the ground, with our detailed instructions and optional phone support also available.

If you (or a clever tradie mate) know your way around a drill; are confident using a masonry drill bit; and are comfortable using metal tek screws with aluminium; it's "Do-It-Yourself" that you can actually do.

Please read the Recommended Uses section to confirm if this product is suitable for your installation site.

Please note that our delivery service is limited to curb side only. Our drivers are unable to drive up driveways, as doing so may result in potential damage.

All of our pump covers are individually made right here in Australia, with an average turnaround time of approximately 3 – 6 weeks.

Your order will arrive in two separate deliveries – an accessories pack via courier, and your main pump cover kit via truck delivery on a pallet.

Standard flat rate shipping starts from just $100 including GST for select Australian capital cities and surrounding metro areas. Your exact shipping rate will be calculated automatically at checkout. Our products can be shipped throughout most of Australia, including Brisbane, Gold Coast, Newcastle, Sydney, Melbourne, Adelaide, Canberra and Perth. Please contact us to confirm shipping rates outside of these areas.

Please add an additional 2 weeks lead time to any orders placed in December due to our Christmas shut down period.

Free Standing Pool Pump Covers

Colour

Depth

Height

Width

Gates

Cost